Archive

Posts Tagged ‘dread extensions’

Dread Extension

May 19th, 2012 No comments



dread extension

How to Make Dread Extensions!



C2g 3.5mm Extension Stereo Audio Isolation Transformer - For Audio Device, Speaker - Extension


C2g 3.5mm Extension Stereo Audio Isolation Transformer – For Audio Device, Speaker – Extension


$33.03


Every installation technician has faced it or soon will – the dreaded humming from the speakers, a telltale sign of a ground loop. Ground loops are caused by voltage potential differences at the ground point on your equipment. Voltages in the range of microvolts up to millivolts or higher can cause ground loops. Ground loops occur when multiple audio/video components are powered from different outlets, most commonly, outlets that are tied to different circuitbreakers or even a different secondary from the power transformer. Ground loops manifest themselves in the form of speaker hum. Our isolation transformer easily connects into your audio/video system and breaks the ground path through cables between components. Start at the component last installed before the ground loop was discovered, and connect the isolation transformer at different ends of the audio/video cable until the ground loop is gone.

Powerbuilt 7/8-Inch and 22mm Offset Oxygen Sensor Socket - 647094


Powerbuilt 7/8-Inch and 22mm Offset Oxygen Sensor Socket – 647094


$12.95


A faulty oxygen sensor is the leading cause of the dreaded check engine light illuminating. Modern engines hove 2 to 4 sensors, so chances are sooner or later one will go bad, especially if they aren’t replaced periodically as part of ongoing maintenance. Worse, sensors are expensive as is the typical shop labor charge to change one. If you have the skills and access to change your own O2 sensor, here’s the perfect socket for the job. It features a 2 inch offset for added reach to grab hold of the sensor and loosening it securely. The 3/8″ square drive is ready for use with an extension bar, ratchet or breaker bar. Since it meets or exceeds ANSI standards, you can confidently reef on it to break loose those fused-on sensors. Millions of Powerbuilt products are used every day around the globe, on the job, at home and in the garage. Powerbuilt tools are built with the performance, features, fit and finish to satisfy the most demanding users. No matter which Powerbuilt tool you select, you will enjoy the added confidence of knowing that all Powerbuilt tools and equipment meet or exceed applicable standards set by the US Government and American National Standards Institute (ANSI). Ready to get serious? Get Powerbuilt tools! -2 inch offset adds options for reaching and turning oxygen O2 sensors -Fits 7/8″ and 22mm O2 Sensors -Premium chrome vanadium steel construction -3/8 inch square drive for use with ratchet, breaker bar, extension bar etc. -Meets or exceeds ANSI standards.

Dread Extentions

April 5th, 2012 No comments



dread extentions

Synthetic Dreadlock Extensions Tutorial


Dread Extensions

February 28th, 2012 No comments



dread extensions

My method of Dread extensions (Part 1)



C2g 3.5mm Extension Stereo Audio Isolation Transformer - For Audio Device, Speaker - Extension


C2g 3.5mm Extension Stereo Audio Isolation Transformer – For Audio Device, Speaker – Extension


$33.03


Every installation technician has faced it or soon will – the dreaded humming from the speakers, a telltale sign of a ground loop. Ground loops are caused by voltage potential differences at the ground point on your equipment. Voltages in the range of microvolts up to millivolts or higher can cause ground loops. Ground loops occur when multiple audio/video components are powered from different outlets, most commonly, outlets that are tied to different circuitbreakers or even a different secondary from the power transformer. Ground loops manifest themselves in the form of speaker hum. Our isolation transformer easily connects into your audio/video system and breaks the ground path through cables between components. Start at the component last installed before the ground loop was discovered, and connect the isolation transformer at different ends of the audio/video cable until the ground loop is gone.

Powerbuilt 7/8-Inch and 22mm Offset Oxygen Sensor Socket - 647094


Powerbuilt 7/8-Inch and 22mm Offset Oxygen Sensor Socket – 647094


$12.95


A faulty oxygen sensor is the leading cause of the dreaded check engine light illuminating. Modern engines hove 2 to 4 sensors, so chances are sooner or later one will go bad, especially if they aren’t replaced periodically as part of ongoing maintenance. Worse, sensors are expensive as is the typical shop labor charge to change one. If you have the skills and access to change your own O2 sensor, here’s the perfect socket for the job. It features a 2 inch offset for added reach to grab hold of the sensor and loosening it securely. The 3/8″ square drive is ready for use with an extension bar, ratchet or breaker bar. Since it meets or exceeds ANSI standards, you can confidently reef on it to break loose those fused-on sensors. Millions of Powerbuilt products are used every day around the globe, on the job, at home and in the garage. Powerbuilt tools are built with the performance, features, fit and finish to satisfy the most demanding users. No matter which Powerbuilt tool you select, you will enjoy the added confidence of knowing that all Powerbuilt tools and equipment meet or exceed applicable standards set by the US Government and American National Standards Institute (ANSI). Ready to get serious? Get Powerbuilt tools! -2 inch offset adds options for reaching and turning oxygen O2 sensors -Fits 7/8″ and 22mm O2 Sensors -Premium chrome vanadium steel construction -3/8 inch square drive for use with ratchet, breaker bar, extension bar etc. -Meets or exceeds ANSI standards.